2021-06-28
1. Ιt συνιστάται η λήψη προστατευτικών μέτρων για υπαίθρια τοποθέτηση σε υπαίθριο χώρο και μέρη εκτεθειμένα στο ηλιακό φως.
2Θαμμένοι αγωγοί ύδρευσης HDPE. Σωλήνες με DN≦Το 110 μπορεί να εγκατασταθεί σε σχήμα σερπεντίνης το καλοκαίρι. Σωλήνες με DN≧110 έχουν επαρκή αντίσταση στο έδαφος και μπορούν να αντισταθούν στη θερμική καταπόνηση, οπότε υπάρχειδεν χρειάζεται να κάνετε κράτηση μήκους σωλήνα. το χειμώνα, δεν είναι απαραίτητο. Κρατήστε το μήκος του σωλήνα.
3. Wκόταεγκατάσταση σωλήνων HDPE, εάν ο χώρος λειτουργίας είναι πολύ μικρός (όπως: φρεάτια αγωγών, κατασκευή οροφής κ.λπ.), θα πρέπει να χρησιμοποιηθούν μέθοδοι σύνδεσης με ηλεκτρική σύντηξη.
4. Wκόταconnecting hot-melt sockets, the heating temperature should not be too high or too long, and the temperature should be controlled at 210±10℃, διαφορετικά θα προκαλέσει υπερβολική συμπίεση out of the fittings and reduce the inner diameter of the water; wκόταinserting the pipe fittings or the pipe interface should be clean, otherwise it will cause the socket to escape and leak; at the same time, pay attention to control the angle and direction of the pipe to avoid rework.
5. Wκόταconnecting hot melt butting, the voltage is required to be between 200~220V. If the voltage is too high, the heating plate temperature will be too high, and the voltage will be too low, and the docking machine will not work normally; the interface should be aligned during docking, otherwise it will cause insufficient butt joint area, insufficient weld strength, and improper crimping; wκόταthe heating plate is heated, the pipe interface is not cleaned, or the heating plate has impurities such as oil and sand, which will cause the interface to detach and leak; heating time it must be controlled well. The heating time is short and the pipe heat absorption time is not enough, which will cause the welding edge to be too small, and the heating time will be too long, which will cause the welding edge to be too large and may form a false weld.
Η Ningbo Fangli Technology Co., Ltd., ως κατασκευαστής με σχεδόν 30 χρόνια εμπειρίας στον εξοπλισμό γραμμών παραγωγής εξωθητών, έχουμε μεγάλη εμπειρία κατασκευής εξοπλισμού και μπορούμε να σας παρέχουμε επαγγελματικές τεχνικές οδηγίες και προτάσεις προμηθειών εξοπλισμού.
https://www.fangliextru.com/pe-pipe-extrusion-line.html
https://www.fangliextru.com/extrusion-equipment-for-type-a-structural-wall-winding-pipe.html